admin

A print head problem usually causes Canon Error code B200, and a support code B200 error notice will appear on the control panel. As a warning, the orange and green lights will continue to blink ten times. The most common solution we’ve heard is to switch off the printer and wait a few minutes for it to cool down. It could be caused by foreign debris in the rollers or a paper jam that has to be cleared. This genuinely works for some people. However, if this doesn’t work, there is another option. This, however, is dependent on the number of cartridges in your Canon printer. To solve this problem, the number of cartridges is crucial. The disadvantage or issue associated with this technique is that it does not reveal which cartridge has a defective print head. So, you’ll have to go through the entire set to find a solution. So, here’s a step-by-step guide that you can use.

If you have a Canon printer with two cartridges, follow these steps:

  • Turn the printer off. Wait for the cartridge carrier to come back to the side. If the carriage becomes stuck, lift the lid and push it to the side.
  • Switch on the printer.
  • Remove the cartridges from the machine. If there is any clogged or dried ink in the nozzles, clean them.
  • Replace the cartridges if necessary. An essential element of this is changing a cartridge to figure out which one is the problem. Insert a new or old working ink cartridge (black or color) with the existing ink cartridge.
  • Check to see if Error B200 is still present.
  • Replace the cartridges until you figure out which one is causing the issue.
  • Now, you must replace the faulty cartridge with a new one.
  • Print a test page.

Canon printer with four color ink:

  • You are supposed to reconnect the power cord and switch on the printer.
  • Next, check the nozzles or run a cleaning cycle. When the printhead cannot be cleaned or accessed, Error B200 occurs.
  • To avoid further printer damage, contact Canon Helpline or a printer specialist if the problem persists.
  • If Canon printer Error B200 persists, it may indicate that the printer’s inside has been damaged. If your printer’s warranty is still valid, contact customer care.
  • Remove all ink cartridges by opening the ink cartridge carriage.
  • Carefully remove the printhead by lifting the lever on the carriage’s side.
  • Clean the printhead to get rid of any clogged or dried ink.
  • Replace the printhead. Replace the ink cartridges in their proper locations.
  • Unplug the printer’s power cord and set it aside for at least 5 minutes, or until it has cooled down.

To avoid further printer damage, contact Canon Helpline or a printer specialist if the problem persists.

How to Fix Canon mx922 Support Code b200?

While using your Canon printer, you may have encountered the error number B200. One must be informed this error is more than a simple error; it is a significant indication that your printer is in poor working order. Because this problem is highly unusual in newly purchased printers, replacing them is reasonable. This indicates that your printer’s life has come to an end, and it’s time to bid it farewell. But if you can’t afford or don’t want to buy a new one, there is a way to eliminate the mistake and gain some extra time with your printer.

How to fix the Canon b200 error code?

Now that you know what’s causing the problem, here’s how to correct it, so your printer keeps working:

Start the printer again:

This strategy does not always work, but it does have a chance of succeeding in some instances. Turn the printer off, disconnect it, and wait at least 2 hours for it to cool. And then, you must restart the computer to see if the Canon mx922 error b200 disappears.

Replace the cartridges:

Replace all of the cartridges and try again. To re-establish the cartridge connection with the printer, remove all old ones, replace them with new ones, or reinstall them.

Clean the printer head and replace it:

Remove the printer head and wipe the gold contacts on the backside with a soft cloth. When you’ve cleaned everything up, make sure the ribbon cable connector is firmly inserted into the printer head before reinstalling it.

After you’ve removed the printer head, run it under hot water to clean away any remaining ink before replacing it.

Reinstall the drivers:

A faulty driver could be one cause of the Canon B200 problem. First, check to see whether reinstalling the printer’s drivers fixes the problem.

One of these solutions will undoubtedly assist you in resolving the issue. If the problem persists, you can contact Canon printer customer service to advise what further you can do.

Canon B200 Error Code:

When your Canon printer displays the dreaded B200 Error, it usually means that the print head has perished! So before you throw out your printer or go out and get a new one, consider the following tips.

  • Firstly, you must remove all of the ink cartridges and replace them with new ones.
  • Now, you are required to remove the print head and clean all of the gold contacts on the print head thoroughly. Please make sure the ribbon cable connector is firmly inserted into the print head itself before reinstalling the print head (this usually applies to older models).
  • After removing the print head, carefully clean it by rinsing all ink out with hot water. Print head cleaning (video) may be of assistance.
  • The next step is to update the printer drivers, as a faulty driver might produce the Canon b200 error code in some circumstances.
  • For at least 2 hours, try turning off the printer and unplugging it from the wall. This can work in some cases.
  • Purchase a new Canon print head and install it on your own. (This is not suggested because buying a new printer is usually not much more expensive.)

One must read this blog if you want to find out how to fix the Canon Pixma b200 error. All you are expected to do is to go through the steps that are given above, as you would be able to find the answer to the significant questions like, can you fix Canon error code b200? 

 

Leave a Comment